Ai Dual-Jacketed 100L 316L-Grade Stainless Steel Reactor

Brand :

Calculated at Checkout
Across International
316 Stainless Steel
220V, 50/60Hz, 1~Phase, 200 watts, 1/4 HP
450 rpm max. (±8%)
38 x 32 x 82" (WxDxH)



Peer review model lead time: 4 weeks

Ai 316L Grade Stainless Steel Reactor Features

  • Dual jacketed. Sealed outer insulation jacket provides best temperature performance inside chamber
  • All wetted parts on main vessel and lid built with pharmaceutical grade 316L SST
  • Shell and tube heat exchanger with 70 tubes for the best condensing results
  • ElectroPolished internal chamber
  • Detachable condenser and collection tanks
  • Dual collection tanks with big sight glass allows you to drain without breaking vacuum
  • High drain port clearance for easy draining or added filtration
  • Large ports (top 12" bottom 6") allows easy chamber cleaning
  • Top placed vacuum port on condenser provides better flow and condensing results
  • No messy cable, with space saving integrated stirring motor controller
  • Heavy-duty stainless-steel frame with swivel casters
  • Built-in flashlight gives you a clear view inside the chamber
  • Positive/negative pressure gauge
  • Matte finish stainless steel
  • Customizable lid for various application
  • Tons of tri clamps adapters available, e.g. tri clamp to hose barb/KF25/NPT
  • Choice of bolted or pin clamp for various pressure applications
  • Flexible bellow condenser connection reduces shipping damage
  • Electric motor and controller model is ETL certified to UL and CSA standards
  • Peer reviewed model (pneumatic motor and controller) is approved to be used with Acetone, Ethanol, Heptane, Hexane, Isopropyl Alcohol, Methanol, and Pentane.


  • Never fill circulated heaters or chillers with water, always use Ai or manufacturer's recommended thermal fluid
  • Always leave ample fluid space in heater reservoir to allow fluid heat expansion
  • Always keep system vacuum passage or drain valve open when heating up circulation jackets
  • Always make sure your vacuum pumps and diffusion pump fluid is clean and within limits






 Electric stirring motor

 220V, 50/60Hz, 1~Phase, 200 watts, 1/4 HP

 Rotation: 450 rpm max. (±8%)

 Starting torque: 3.0 N.m

 Rated toruqe: 1.54 N.m

 Built-in gearbox ratio: 3:1 to 180:1

 Controller: Delta, UL listed

 Pneumatic stirring motor

 - Power: 1/4 HP

 - Rotation: 450 rpm max. (±8%)

 - Compressed air pressure range: 30 to 80 psi (0.2 to 0.55 MPa)

 - Working temperature: -10C to +70C

 - For constant use: set rpm to 80% of maximum rpm

 - Motor lubricant

Daphne Eponex EP-No. 1

Check/replenish/replace every 500 hours

 - Air lubricant

Type: JIS K2213-1 (ISOVG32)

Recommended products: Shell Vitrea Oil 32, JOMO Turbine 32, COSMO Turbine 32

Speed: 2-3 drops per minute

 - For safety purpose, detach compressed air supply when not in use, left un-attended or at night

 - Do not run motor un-loaded

 - Set Air Adjuster to minimum at initial run, make sure motor is working properly, before increasing CFM

 - Before inspecting unit, stop the motor and detach air supply. Do NOT inspect unit when motor is in action.

 - Make sure exhaust port/hole is clear from any debris or blockage

 - Check every 2-3 days: Air Lubricant, Air Filter water drain

 Port configuration

 Lid: 6" triclamp

 Center motor: 3" triclamp

 Drain port: 6" triclamp

 Drain port on/off valve: 2" triclamp

 Vacuum port, condenser fluid port, etc: 2" triclamp

 Jacket fluid ports: 1" male NPT

 Main vessel

 Volume: 100L

 Material: 316L grade stainless steel

 Interior finish: ElectroPolished


 Structure: propeller, 3-blade, dual-layer (standard)

 Style: quick-change

 Material: 316L grade stainless steel

 Detachable length: 20 inches

 Center fluid jacket

 Volume: 22L

 Material: 304 grade stainless steel

 Outer insulation jacket


 Material: 304 grade stainless steel

 Collection tank

 10L x 2


 All wetted parts 316L grade stainless steel on main reactor body

 Rest of reactor in 304 grade stainless steel

 Main Condenser

 Style: shell and tube heat exchanger

 Number of tubes: 70

 Condensing area: 0.89 m2


 Ultimate vacuum level: 1 Torr

 Maximum positive pressure (C1D1 peer reviewed to 15 psi)

Main vessel: 70 psi

Fluid jacket: 40 psi

 Temperature range

 -55°C to +250°C (-67°F to +482°F)

 Temperature sensor/display

 Regular: BOOST.TTA.0101, -200C to 480C, 50.5 clamp

 Explosion proof: BOOST.TTA.0102, -200C to 480C, 50.5 clamp

 Sealing gasket

 Food grade Viton

 Main Mounting Frame

 Heavy duty 2 x 2" 304 grade stainless steel, mounted on four casters

 Drain port ground clearance

 Drain port: 19.5 inches

 Drain valve: 14 inches

 Unit/shipping weight

 255 Lbs / 350 Lbs

 Unit/shipping dimensions

 38 x 32 x 82" (WxDxH)


 ETL tested to UL and CSA standards

 C1D1 peer review by PSI (optional)


















Shell and Tube Heat Exchanger



Standard Quick-Change 316L Stainless Steel Propeller Agitator





                Across International                   usa-lab-logo-with-phone-number.jpg

Across International
316 Stainless Steel
220V, 50/60Hz, 1~Phase, 200 watts, 1/4 HP
450 rpm max. (±8%)
38 x 32 x 82" (WxDxH)

Customers Also Viewed